18 November 2026

Cymbal Sizzler vs Rivets: Which Sizzle Is Right for You?

Cymbal Sizzler vs Rivets: Which Sizzle Is Right for You?

Cymbal Sizzler vs Rivets: Which Sizzle Is Right for You?

Cymbal with rivets beside a chain sizzler

A sizzler is a removable attachment that rests rattling parts on a cymbal. Rivets are small metal pins fixed through holes drilled in the cymbal. Both add a shimmering, rattling sizzle. A sizzler is the reversible way to try the sound, and rivets are the permanent way to build it into one cymbal. If you play a cymbal for years in the same role, rivets give the more integrated, stable sound. If you are still deciding whether you like sizzle at all, start with a sizzler.

This guide explains how each works, what each does to sustain, how many rivets to use, and how to fit them without damaging the cymbal.

Templeofsound
Find Your Cymbal Sizzle
Explore percussion instruments and accessories from Temple of Sound Distribution as you decide which cymbal sound suits your playing.
Visit

TL;DR

  • A sizzler (a chain, or rivets hung above the edge) sits on the cymbal and can be taken off. Rivets are fitted into drilled holes and stay there.
  • Both lengthen the wash of a cymbal’s decay into a continuous shimmer. Rivets blend into the cymbal’s own movement, while a sizzler tends to sit on top of it.
  • Start with two or three rivets. More rivets restrict the cymbal’s movement and dull its response.
  • Drilling too near the edge risks cracking, so keep rivet holes well inside the rim.
  • Removing rivets restores the tone, though the holes stay.

Table of Contents

What each one actually is

A sizzle cymbal is, in the usual definition, a cymbal with rivets, chains or other rattles added, either through drilled holes or by an attachment called a sizzler. That one sentence holds the whole difference.

Rivets are short metal pins, usually brass or steel, that sit loosely in holes through the bow of the cymbal. When you strike the cymbal, the rivets bounce in their holes and buzz against the metal.

A sizzler is anything that adds the buzz without holes. Common types are a small ball chain laid across the cymbal’s surface, a clip-on bar that holds rivets just above the rim, or a rattle strung from the stand. The same reference notes that these chains can be fixed, adjustable in length or completely removable, and that rivet-style sizzlers hang the rivets above the rim, usually in two groups opposite each other.

How installed rivets differ from removable sizzlers

The reason people reach for either one is old. According to Modern Drummer, jazz drummers began drilling cymbals for rivets in the 1930s to create a smooth, soft pad of sound under the ride pattern. Swish and pang cymbals were traditionally sold with rivets already fitted, and many early rock drummers used a thinner secondary ride with rivets.

How the sound differs

Both options add sustain in the form of buzz. The difference is in how the buzz is made.

Installed rivets

Rivets live inside the cymbal’s vibration. The cymbal moves, the rivets move with it, and the result is a sizzle that feels part of the cymbal’s own decay. Because the rivets sit in the bow, their number and position change how freely the cymbal vibrates. The type of cymbal matters too: weight and thickness shape how long the sizzle lasts, as drummers have long pointed out.

Independent reviews show the effect on specific models. In a MusicRadar review of a set of cymbals, the riveted 12-inch hi-hats had a cutting dimension when closed, and the half-open sound was especially sharp and shrill. The same review described the 18-inch crash as short and dry in sustain. These are observations about particular cymbals rather than a rule, but they show that rivets can sharpen a hi-hat as readily as they can soften a ride.

Removable sizzlers

A sizzler sits on the surface or above the rim, so it responds to the cymbal rather than becoming part of it. The sound is usually a more obvious, slightly separate rattle, and it varies with where you place it and how long the chain is. Its great advantage is that you control it. Lay a chain across the bow, listen, move it, shorten it, or take it off before the next song.

A sizzler also works on a cymbal you would never drill: a vintage ride, a cymbal you plan to resell, or one with a thin, delicate rim.

Sizzler vs rivets at a glance

Removable sizzler Installed rivets
Reversible Yes, instantly Rivets come out, holes stay
Cymbal modification None Drilled holes
Sound character Sits on top, more obvious rattle Blends into the cymbal’s own decay
Adjustability Position, length, number all easy to change Fixed once fitted, though pins can be swapped
Best for Trying the effect, vintage or valuable cymbals, switching between gigs A cymbal with a permanent sizzle role
Main risk Can shift or rattle on its own during a set Cracking if holes are badly placed

When to choose a removable sizzler

Choose a sizzler when any of these apply:

  • You are not sure you like the sound. Sizzle suits some cymbals and some songs, and sounds wrong on others. Hearing it first costs nothing permanent.
  • The cymbal is valuable or vintage. Holes lower the originality of a cymbal, and a sizzler avoids that. Our guide to cymbal hole size and protecting vintage cymbals explains how much a hole matters on older cymbals.
  • You want the effect only on some gigs. A sizzler lets one ride cymbal be dry on Tuesday and shimmering on Saturday.
  • You are testing before you drill. Many drummers use a sizzler to find the right placement, then copy it with rivets.

When rivets make more sense

Rivets are the better long-term choice in these situations:

  • The cymbal has one job. A secondary ride, a swish or a dedicated jazz ride is likely to stay riveted for life.
  • You want a seamless sound. Rivets that move with the cymbal avoid the sense of a separate rattle.
  • You want nothing to fall off or shift. A pin in a hole stays where you put it.
  • You are building a particular sound. Number, spacing and material are all variables you can tune.

There is a reassuring fact for the cautious: removing the rivets restores the cymbal’s previous tone, and ordinary rivet holes make an inaudible difference. Large or numerous holes will dry the sound, and holes may slightly reduce resale value, so go modestly.

How many rivets, and where

This is where the real tuning happens, and where most beginners overdo it.

Drummers in forum discussions commonly settle on two or three. One rivet often sounds like an individual rattle, while two placed apart give a more even decay, and more than three can restrict the cymbal’s movement. Treat this as practical player experience rather than a law, because it depends heavily on the cymbal.

Modern Drummer notes that placements have included both evenly spaced patterns and clusters of a few rivets close together to temper the sizzle. In practice:

  • Evenly spaced rivets give a broader, more uniform shimmer around the cymbal.
  • Clustered rivets give a more focused, controlled sizzle, which can be easier to live with in a quiet room.
  • Heavier rivets produce a louder, more defined buzz. Lighter rivets give a softer, quicker one.
  • Position along the bow changes how much the rivet moves. Where it moves most is where it sizzles most.

The number and positioning also tie to musical use. A jazz ride under brushes wants a soft sizzle that supports the ride pattern. A rock secondary ride wants something that cuts. A hi-hat with rivets in the bottom cymbal wants a sharp, tight chick. Our walkthrough on installing sizzle rivets, starting with three shows how to build up from a small number and listen to the wash before adding any more.

How to fit rivets without cracking the cymbal

Fitting rivets is a small job, but the cymbal cannot be un-drilled, so slow down.

  1. Choose the cymbal and the number. Plan for two or three. MusicRadar’s workshop demonstration used three rivets, 2 inches from the edge and 1 inch apart, which is a sensible starting layout.
  2. Mark the positions. Use a marker and a ruler, and mark on both sides if you want to check alignment.
  3. Make a pilot dent. The same guide recommends a centre punch to create an indentation so the drill bit does not wander.
  4. Drill to match the rivets. Use a bit sized to the pin, and go slowly. If you are unsure about sizes, our page on which bit size protects a cymbal covers it.
  5. Insert and flatten the ends. Put the rivet through, then flatten the ends just enough so it stays in but still moves.
  6. Play it in. Hit the cymbal in the way you will play it and listen for the wash. If it is too much, remove one rivet.

The main warning is about distance from the edge. MusicRadar’s guide cautions that drilling too close to the cymbal edge could cause cracking. Edges carry stress every time you hit the cymbal, so a hole there is a weak point. If you want to understand why cymbals crack in the first place, our five-minute routine to prevent cymbal cracks explains the causes. And if a mounting hole has already started to wear into a keyhole shape, simple keyhole repairs are covered separately.

Sizzle without drilling: other options

If you want the sound without holes, you have several types of sizzler available:

  • A ball chain laid across the bow. The simplest version. Shorter chains give a tighter sizzle, longer ones a washier one.
  • A clip-on rivet bar. Suspends rivets just above the rim, usually in two groups opposite each other.
  • A stand-mounted rattle. Sits off the cymbal and gets its buzz from contact with the edge.

All of them are easy to remove and put back. Their weakness is that they can creep out of position over a long set, so check them between songs.

Sizzle in the mix

Sizzle is a sustained, high-frequency texture, so it behaves differently in a recording than a plain ride. It spreads across the overheads and can pile up with room reflections. If you record or mix drums, microphone distance matters: check our guide on cymbal mic placement and the 3:1 rule before you lock in overheads. In the mix, the way an echo or reverb tail overlaps the sizzle also shapes how washy it feels, and this explainer on echo versus reverb settings helps you set tails so they do not smear the shimmer.

Our view

We think sizzle is best treated as a decision about the cymbal, not the effect. Ask what role this cymbal will play for the next few years. If the answer is a clear one, fit rivets and commit to it. If the answer is “I’m not sure”, use a removable sizzler first.

The other half of the decision is the cymbal underneath. Sizzle adds to whatever the cymbal already has, so a cymbal with a good, even decay is the best starting point. That is why we stock handcrafted cymbals and sticks that are made to be played hard and heard clearly, and why we like to help drummers find the base sound before they add anything to it.

Start small, listen, and change one thing at a time.

Will

Start with a cymbal worth riveting

If you are choosing a cymbal for a sizzle role, our Alchemist Collection of cymbals is where to look, and our B20 hand-hammered range is there for drummers who want a handcrafted sound. We are the exclusive UK distributor for Alchemist Cymbals and the London Drumstick Co., and you can also build a custom drumstick to match your ride pattern.

Templeofsound

Membership is free to join, and our Pro Member plan is £4.99 per month and our VIP Member plan is £9.99 per month. Details are on our home page. Drum shops and retailers can also ask about trade accounts there.

FAQ

Is a sizzler the same as rivets?

No. Rivets are pins fixed through holes drilled in the cymbal. A sizzler is a removable attachment, such as a chain or a clip-on rivet bar, that adds a similar buzz without holes. Both are grouped under the sizzle cymbal idea, but only rivets modify the cymbal.

Do rivets ruin a cymbal?

Not when they are done carefully. Ordinary rivet holes make an inaudible difference, and taking the rivets out restores the previous tone. Keep holes well away from the edge, since drilling too close can cause cracks, and use a small number of holes.

How many rivets should I put in a cymbal?

Two or three is the common starting point. One can sound like a single rattle, and more than three tends to restrict the cymbal’s movement. Fit two first, listen, and add a third only if you want more wash.

Can I use a sizzle on a hi-hat?

Yes. Rivets in a bottom hi-hat are a long-standing option. In one independent review, riveted hats added a cutting edge when closed and sounded sharp and shrill when partly open, so go lightly if you want a subtler effect.

Sources

READY TO HEAR THE DIFFERENCE?

Hand-crafted cymbals and custom drumsticks, straight from the foundry.